VW TDI forum, Audi, Porsche, and Chevy Cruze Diesel forum banner
1 - 4 of 4 Posts

·
Registered
Joined
·
9 Posts
Discussion Starter · #1 ·
So, since the MK6 is not available with HomeLink and I wasn't about to shell out a billion bucks for one, I decided to do a DIY garage door opener install on my MK6. It is rather easy to do.
I do not take credit for this mod, I used the MK5 DIY posted here:http://forums.vwvortex.com/showthread.php?2692684
Here is my DIY, which is basically going into more details.

Here are the tools and parts needed for this job:
* Torx 20 driver
* Trim tool (not necessary but recommended)
* Flashlight or well lit work area where the car is
* Soldering iron
* Solder
* Electrical wires (I used black/red for remote power and yellow for remote switch)
* Wire cutters
* Wire stripper/crimper
* Momentary push button switch (I used Radio Shack 275-1566 which is a soft touch, if you'd like a click type for more button feedback you can use 275-618 which I believe has the same dimensions around the switch button)
* 2 wire taps with their male electrical connector
* Screwdriver to take your remote apart (mine had a small Phillips screw on it)
* Garage door remote (I used the one that came with my Garage door opener since it was powered by a 12 volt battery, it's a Genie GIT-1)
* Rotary tool (Dremel) with cutting disc and round file
* File
* Super Glue (gel type is best)

Most of these are shown on here:



Step 1:
Start by removing your stock shifter base trim, you can use the trim tool there, I just grabbed the front part of it and pulled it off (passenger side came out much easier on my car):





Here is a picture of the clips that hold the trim in:


Step 2:
Below that, you will see two Torx 20 screws holding the ashtray piece that contains the buttons, remove these:



Step 3:
Lift the ashtray piece up and unplug the two connectors (one for the ESP switch, one for the cigarette lighter), then take the ashtray piece out of the car:




As you can see, there is plenty of room below the ashtray to fit your remote:


Step 4:
Take your remote apart:



You will be left with the circuit board with battery in place (mine uses a 12 volt battery, but a lot of garage door opener use a 3 volt battery). If your remote uses a 12V battery, you can hardwire it to the car and never have to worry about the battery going bad (you do not re-use the battery). If it uses a 3V battery, you will not be hard wiring the remote to the car, you will have to replace your remote's battery when it goes bad (to give you an idea, my remote's battery went bad after almost 9 years of daily use so they last quite a long time usually).



Step 5:
Now locate the switch on the remote, on the opposite side you will see that all the switch does is connect 2 parts of the PC board and that activates your remote. Now what you have to do is solder a wire to each one of these point. Each wire will go to one of the two terminals on your switch. If you have a 12V remote and want to hard wire it, now is the time to solder wires to the battery terminals, please pay attention to the polarity. I used black for ground (-) and red for power (+). I know both wires look red but one is red/black on my wires. Make the wires long enough for them to come out of the remote and to your switch and power connection:




Step 6:
Use the round file on the Dremel to make 4 notches in the case of the remote to feed the wires thru, and re-assemble your remote (I removed the rubber button from the remote so it wouldn't get pressed inadvertently:



Step 7:
Take your ashtray piece, flip it over and remove the blank switch you wish to use, I am using the one next to the ESP button, you can always swap the 3 center buttons around later if you change your mind on the location of the switch, each end switch are a different shape though:





 

·
Registered
Joined
·
9 Posts
Discussion Starter · #2 ·
went thru and edited each pic since the forum doesn't support HTML tags for pics, took me a while just for me to find out you are limited to 22 pics :( :umm
 

·
Registered
Joined
·
9 Posts
Discussion Starter · #5 ·
Yes, the limit is so that each post doesn't run 10x the normal length. It causes performance problems. The img tags are the same on the vortex. Most don't allow html because it's not as secure.
Oh lol I see what you did, posted it in two posts !
flickr requires you use their HTML link because of EULA that say if you post the pic on another website there has to be a link back to flickr so basically I get a whole HTML code I can just paste and go, otherwise I have to take each pic's link and click on the IMG tag button and paste :)
 
1 - 4 of 4 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top